Level I Certified Infrared Thermographer

J.N. Allinson Associates, Inc.
Allinson Infrared Inspection Services, Inc.
222 University Blvd. North #2
Jacksonville, FL  32211

904-721-2177

www.allinson.com

Abstract:

Marine surveyors are to the marine industry as predictive maintenance technicians are to factories and building inspectors are to the commercial and residential real estate industries. 

A marine surveyor’s opinions are relied upon to document the condition, value, and safety of the vessels they inspect.  Marine surveyors rely heavily upon experience and what they can see, hear, and feel.

Traditionally, visual anomalies seen with the unaided eye are often the sole basis for ordering destructive testing. 

In this presentation we will show that under proper and controlled conditions, infrared thermography is an effective and appropriate non-destructive testing (NDT) tool which can detect anomalies and potential defects prior to destructive testing.

Level III Certified Infrared Thermographer

Delta T Engineering, LLC
136 Main Street
Metuchen, NJ  08840

877-321-0576

www.deltatengineering.com

fred@deltatengineering.com

Abstract:

Thermography is a proven technology for detecting elevated temperatures within operating electrical distribution systems.

Typically performed on an annual basis, infrared inspections can detect evidence of overheating caused by loose/deteriorated connections, overloaded circuits, and imbalanced loads.

While infrared inspections can be valuable in helping to prevent unexpected failures, they provide a single “snapshot”, leaving the subject components unmonitored for the balance of the year.

Recent advances in technology have resulted in wireless sensors that monitor for the same types of defects that are detectable by thermal imaging.

When permanently installed on electrical enclosures, these sensors can provide year-round monitoring of electrical system components and can immediately alert personnel when problems arise.

This paper will discuss the theory and application of the Delta T Alert monitoring system and how it can be used to complement and enhance the effectiveness of an existing infrared inspection program within commercial office buildings.

Installation and set-up procedures of the system will be discussed along with actual case studies.

PdMA Corporation
5909C Hampton Oaks Parkway
Tampa, FL  33610

813-621-6463, ext. 124

www.pdma.com

noah@pdma.com

Abstract:

In the wake of sweeping energy regulations and increased competitive strategies, aging facilities are no longer being allowed to perform at sub-energy efficient levels.

Ultimatums have been handed down to facilities to either increase their energy efficiency levels or face the inevitable plant closure possibility as corporations choose which facilities are too costly to maintain.

  For those working at these aging facilities, asset reliability and energy efficiency have never been more important. 

This paper will follow the efforts of multiple facilities within a corporation to increase their productivity through reliability and efficiency in an effort to survive the corporate axe.

Level III Certified Infrared Thermographer

Brady Infrared Inspections, Inc.
935 Pine Castle Court
Stuart, FL 34996

772-288-9884

www.bradyinfrared.com

jbrady@bradyinfrared.com

Abstract:

Throughout the evolution of infrared technology for predictive maintenance applications,
electrical system inspections remain the cornerstone of the industry.

Despite being somewhat overshadowed in recent years by building science applications, the demand for infrared inspections of electrical systems remains high.

Accurate diagnosis begins with understanding electricity and what causes thermal anomalies.

This presentation will cover several types of defects that may be encountered during an infrared inspection including those associated with compromised connections, overload conditions, load imbalances, harmonics problems, and inductive heating.

Examples of these problems come from a multitude of settings including industrial, manufacturing, utility, and commercial sites.

The theory behind each type of defect, its thermal signature, and how to accurately confirm each will be discussed.

ISC Building Diagnostics
4504 Magnolia Ridge Drive
Waxhaw, NC  28173

704-200-6367

www.iscbuildingdiagnostics.com

www.infraredsurvey.com

Abstract:

Testing and balancing of HVAC systems is important not only for energy and design requirements, but also for the comfort of building occupants.

It’s not easy to see if someone is uncomfortable and impossible to make everyone comfortable.  Thermal imaging has proven to be a useful diagnostic tool for detecting performance and comfort problems in building envelopes.

In some cases, performance issues are caused by deficiencies in the building envelope while others are related to HVAC system components. 

This paper discusses the use of an infrared camera to diagnose and solve problems with HVAC air distribution which, if incorrect, can cause significant performance and comfort issues.

PPL Susquehanna, LLC
769 Salem Boulevard
Berwick, PA  18603

570-542-1673

jrfallbright@pplweb.com

Abstract:

A good thermography program is essential to reliable power generation and distribution.  Routine thermographic surveys identified hot spots on the connections to the high voltage bushings on the main output transformers at the Susquehanna generating station. 

These hot spots were different than those found in the past with infrared.  The connection temperatures would be elevated one day and normal the next. 

This paper will show how continuous monitoring of the connections gave insight into an on-going condition and allowed continued generation until a planned outage.

  Repair of the connections validated the infrared results and provided insight for future work.

UE Systems, Inc.

914-592-1220
800-223-1325

www.uesystems.com

mkgoodman@att.net

Abstract:

Ultrasound and Infrared are complementary technologies for generalized PdM activities.  Ultrasound will “hear” what infrared might not “see”. 

Many IR thermographers are now incorporating ultrasound scans of enclosed electric cabinets as part of their inspection protocol to avoid potential arc flash incidents.

Historically, predictive activities for both technologies cover more than just electrical inspection; they might include inspection of bearings, gears, and valves to name a few.  While sound quality and trending amplitude changes are often the most common methods of identifying issues ultrasonically, there are many situations that will call for more detailed analysis to help determine the severity and type of problem.

Ultrasound instruments are now capable of adding sound imaging through spectral analysis to enhance the diagnostic process. 

This presentation will examine ultrasound imaging for electrical, mechanical and valve leak diagnostics. 

The principles of spectral analysis as it relates to ultrasound inspection will be explained and clarified through case histories and actual examples of faulty bearings, gears, valve leaks, and electric emissions.

Griggs Thermal Imaging
2160 Autumn Place
Columbus,  Ohio  43223

614-272-8266

mark@griggsthermalimaging.com

Abstract:

From the first time that I was exposed to infrared thermography I was hooked on it. 

Working for one of the big three auto companies as a Journeyman millwright, I would routinely escort a contractor that was hired to do our quarterly infrared survey on electrical and mechanical equipment.

After a while my company decided to obtain their own camera in order to conduct infrared inspections using in-house personnel. 

I was one of two people selected for Level I and Level II training.

Utilizing information from our in-house infrared inspections, our company was able to realize some really big cost savings and save a lot of downtime. 

We even used it to help ensure there were not any hot spots after a fire at the plant, as well as locating roof drains that had been damaged during a roof resurfacing.

After retiring from the auto industry, I attended an IR/INFO conference in Orlando.  What I learned there helped me decide to start my own infrared inspection business. 

This paper will discuss my experience with thermography prior to, and after starting my own inspection firm along with advice to others seeking to start their own infrared inspection business.

Kilawatt Technologies, Inc.
Shelburne, VT 05482

802-985-2007

pgrover@kilawatt.com

Abstract:

Energy Systems Diagnostics is a relatively new crossover predictive/condition monitoring technology.

ESD gathers and analyzes energy data that are used to develop control changes and algorithms to increase operational efficiency of energy systems. 

In addition to significantly cutting energy costs, clients can greatly reduce equipment service and replacement costs. 

ESD can be applied to facilities of any size including large commercial and institutional buildings as well as manufacturing facilities.

This paper describes the history and application of ESD and how it utilizes both wired and wireless remote sensors to monitor the electrical and mechanical performance of HVAC systems. 

This paper will also address how to integrate ESD with infrared thermography and other predictive/condition monitoring technologies to provide even greater value to clients.

Level II Certified Infrared Thermographer

United Infrared
8472 Adams Farm Road
Randleman, NC  27317

760-593-2339

www.unitedinfrared.com

jrfallbright@pplweb.com

Abstract:

Although thermal imaging has long been used in the identification of moisture problems in buildings, it is often not the primary tool utilized due to a perception of high imager costs.

Over the past few years, prices on infrared imagers have been tumbling due to the introduction of the microbolometer sensor, mass production, and economies of scale.

At present, even entry level IR cameras can perform quite well when it comes to moisture mapping.  Due to the effects of evaporative cooling, an IR camera can complement the forensic moisture audit by quickly and non-destructively identifying the location and size of moisture damaged areas. 

This presentation describes how we were able to incorporate this technology into our business and reviews some of the many cases in which we successfully detected mositure using infrared thermography.

Level III Certified Infrared Thermographer

NDE Institute of Trinidad, Ltd. / Thermal Diagnostics Ltd.
15 Robertson Street,
Les Efforts East

San Fernando, Trinidad & Tobago, West Indies

868-653-9343
868-657-6572

www.learnndt.com

www.tdlir.com

sjames@learnndt.com

Abstract:

The condition of a power generation plant’s generator stator cores is an important consideration any time repair work is to be carried out on a generator.

Downtime of the generator must be kept to a minimum and there is no room for errors or unforeseen problems prior to start up.  Finding all areas on the stator core that can result in premature failure is imperative before the unit is reassembled and put back into service.

This paper will discuss several case studies where both loop tests using Thermography and ELSID tests were carried out on gas and steam generator stator cores for the purpose of identifying laminations and winding shorts. 

This paper also discusses the method of repairs and re-inspections that were performed after problems were identified.

With Thermographic images of actual stator core faults both before and after repairs and comparisons with ELSID testing, this paper will benefit all in the generator maintenance and inspection field.

It also serves as a good training tool for thermographers who wish to perform this type service. 

James, Sonny
IACT Certified Clinical Thermographic Technician

Managing Director

Level III Certified Infrared Thermographer

Thermal Diagnostics Limited - Medical Division
15 Robertson Street,
Les Efforts East

San Fernando, Trinidad & Tobago, West Indies

868-653-9343
868-657-6572

www.infraredclinic.com

info@tdlir.com

Abstract:

Digital Medical Thermal Imaging has been around for several decades and has proven itself time and time again to patients and doctors.

The benefits of such imaging to both the physician and patient are invaluable when a diagnosis via conventional structural imaging and standard physical examinations are inconclusive or do not provide relief to the patient.

This paper will discuss the benefits of Medical Thermography for both men and women from head to toe.

It will also discuss womens’ breast imaging and why all women should get imaged with thermography. 

Several intriguing case studies that the author came across at his Medical Thermography imaging center over the past year will be presented as well.

FLIR Systems, Inc.
25 Esquire Road
North Billerica, MA  01862

978-901-8000

www.flirthermography.com

Abstract:

Thermal imagers have long been used to detect evidence of problems within a wide variety of systems and structures including electrical distribution systems and building envelopes.

  In order to fully quantify the severity of problems other information is often critical such as electrical load data and moisture levels.  Recent developments now permit wireless transmission of vital diagnostic data from clamp-on ammeters and moisture meters directly to the infrared camera.

This paper will discuss how FLIR’s revolutionary MeterLink technology can help thermographers to document electrical load conditions including energy consumption and load imbalances. 

This paper will also show how building inspectors and restoration specialists can quantify and document moisture levels in building structures, providing clients and insurance companies with quantified recommendations for dry times and damage estimates.

Naval Sea Systems Command (NAVSEA)
2341 Jefferson Davis Highway
Arlington, VA  22202

202-781-1274

rick.kurek@navy.mil

Abstract:

According to the National Fire Protection Association (NFPA), an arc flash is defined as "a dangerous condition associated with the release of energy caused by an electric arc."

An arc is a high-impedance discharge of electricity through the air that causes light and heat.  The temperature of an arc can reach up to 6000 degrees C. Most switchboard components can only withstand these temperatures for about 0.25 seconds before sustaining damage.

Arcing Faults can cause damage to power distribution systems since the inherent operational characteristics of the circuit breakers may not isolate the affected conductors for several seconds due to the relatively low current levels identified with this type of fault.

This paper will discuss how the US Navy is leading the way in Arc Fault Detection (AFD) Technology and has teamed up with Johns Hopkins APL to develop AFD Systems designed to detect and extinguish high resistance arcing faults.

Use of these systems has significantly reduced, if not eliminated any significant damage, from Arc Faults in switchboards and load centers protected by AFD Systems. 

Inspiritus Equine, Inc.
8 Golden Gate Circle
Napa, CA  94558

707-738-7110

www.InspiritusEquine.com

jrobsondvm@
inspiritusequine.com

Abstract:

Infrared Thermography (IRT) has many uses in the equine industry.  In biological systems the detection of surface heat is directly correlated with changes in circulation, thus providing evidence of inflammation or decreased perfusion. 

Currently, the diagnosis of equine back pain is subjective, reliant on the veterinarian’s ability to palpate using his or her hands, and on the trainer’s or rider’s knowledge of how training and behavioral problems may relate to equine back pathology and saddle-fitting problems. 

Modalities such as radiographs or ultrasound provide anatomic evidence of pathologic changes, but require specialized machines, are limited by location, and are not generally feasible in-field for spinal evaluation.

Thermal imaging provides a safe, quick, objective image of equine back inflammation, and is a useful tool in proper saddle-fitting. 

The use of IRT in the equine industry provides objective evidence of equine pain that can help the human handlers to better understand their horses and subsequently effect positive changes that promote maximum equine performance and longevity.

Stockton Infrared Thermographic Services, Inc.
& United Infrared, Inc.

8472 Adams Farm Road
Randleman, NC  27317

888-SCAN-4-IR

www.unitedinfrared.com

info@unitedinfrared.com

Abstract:

Information technology (IT) managers are worrying more about heat in their data centers every day. 

The reliable and efficient operation of the power, cooling and support systems are vital to the continuous flow of information in these mission critical facilities.  Getting as close to 100% uptime or "availability" at data center facilities is a necessity, as a loss in power in a data center can cost the owner millions of dollars.

Now, owing to the ever-increasing cost of electricity and grid capacity issues, data center operators are now exploring the idea of raising the temperature set-points from 70 degrees F to 80 degrees F. 

This is no small market...it is estimated that data centers will consume 100 billion kWh of electricity by the end of this year. 

This paper will explore the traditional P/PM use of IR and the merits of thermally mapping the data center to validate CFD modeling used in the design phase, and so that problems to the cooling system can be found and documented and confirmed after repairs.

Level II Certified Infrared Thermographer

BPI Certified Building Analyst

Infrared Imaging Services
PO Box 221
New City, NY  10956

845-641-5482

www.infraredimaging
services.com

Abstract:

The recent explosion in energy conservation awareness and government stimulus funding has led to an increase in requests for energy audits by homeowners seeking to lower their utility bills.

The thermographer who has chosen to introduce the Energy Audit to his/her line of services may find that audits and related services can be time intensive and low-profit if they lack the experience and strategies necessary to optimize their efforts.

Beginning with audit execution and ending with a comprehensive report, this paper details practical strategies to reduce on-site time and maximize profits by referencing actual infrared survey results.

Tanner Contractors
17 Echo Ridge Drive
Saratoga Springs, NY  12866

518-526-5167

www.NYinfraredscan.com

Abstract:

The price of infrared cameras has come down dramatically over the past several years.

There has also been a vast expansion in media coverage of this exciting technology as demonstrated in the Gulf of Mexico oil spill, television episodes featuring home energy audits, pest inspections, and the expanding role of infrared in space exploration.

The average building inspector, pest management company and roofing supplier remains skeptical to the potential of thermography due to equipment prices, and thermographer training and experience requirements. 

The uncertainty of demand and need to justify the required investment of time, funds, and staff training are often obstacles in the way to incorporating this technology into a company’s business portfolio.

In response to these concerns, NYINFRAREDSCAN.COM has developed a business plan that targets the potential emerging market by selling the product, training, and experience needed to confidently open up this market.

NYINFRAREDSCAN.COM offers all trades the potential of in-house marketing IR with little monetary investment up front. 

The reward is increased sales, exposure, and the label of being the local infrared experts and go-to guys. 

This paper will explain our business model and how success comes from one sale generating into an overall market success.

• Thermographers
• Process Control Supervisors
• Maintenance Managers
• Loss Control Specialists
• Reliability Engineers
• P/PM and NDT Personnel
• Manufacturers
• Quality Assurance Inspectors
• Home and Building Inspectors

• Education
• Learn New Technology
• Networking
• See Latest Developments
• Share Ideas
• Discover New Applications & Techniques